How to Troubleshoot Issues with Reading CD, CD-R, CD-RW, and DVD Discs

You receive the following Errors 

application name is not a valid win32 application.

-or-

A device attached to the system is not functioning.

-or-

A required file kernl32.dll was not found.

-or-

Not enough memory to run this application.

-or-

Cannot find the file(s) needed to start this application.

-or-

Error Reading From File [Installer Error 1305]

-or-

Unable to find Setup.exe

-or-

CDR-101

-or-

Unable to read drive drive letter:

-or-

Insufficient Memory

Problems reading from a disc may also produce the following symptoms:

• The disc label does not appear in Windows Explorer.

• The contents of the disc will not display in Windows Explorer.

• When you insert the disk in the drive or read a disc, the computer stops responding.

• The disc does not eject from the drive.

• Reading from the disc takes an exceptionally long time.

Troubleshoot Error Messages

To troubleshoot error messages, note the specific error message, and then search the Microsoft Knowledge Base for information about this message.

To view the Microsoft Knowledge Base, visit the following Microsoft Web site:

http://support.microsoft.com (http://support.microsoft.com/)

If the error message that you receive refers to a file name, note the name of the file. Try to copy the file to your hard disk in Windows Explorer. If you receive a different error message when you copy the file, search the Microsoft Knowledge Base for information about the new error message.

If you cannot find a Knowledge Base article about your disc read error message, try the following methods to troubleshoot the problem.

After each method, test your whether the disc can be read from. To do this, open or copy the file in question. If the error or symptom does not refer to a specific file, run the program from the disk to test whether the method of troubleshooting was successful.

1. Examine the Disc

Remove the disc from the drive, and then examine the disc for damage such as warping or large scratches. If the disc is damaged, contact the manufacturer about a replacement CD.

If you experience problems with a DVD disc, make sure that you insert the DVD into a DVD drive not a CD-ROM drive.

2. Clean the Disc

To clean the CD-ROM or DVD-ROM, use a disc cleaning kit, or gently wipe the silver side of the disc with a soft, lint-free cotton cloth. Do not use paper cloth as this can scratch the disc. Wipe the disc from the center, outward. Do not use a circular motion as this can scratch the disc.

If this does not resolve the issue, clean the disc by using a water-dampened cloth or a commercial CD cleaning solution or DVD cleaning solution. Dry the disc thoroughly before you put it into the drive.

3. Test the Disc in a Different Drive

If your computer has multiple CD-ROM drives, CD-R drives, CD/RW drives, or DVD drives, test the disc in the other drive. For DVDs, make sure that the drive has a DVD logo on the front. If the disc works in another drive, the original drive may not be properly reading the disc. Please seek help from your computer manufacturer or disc drive manufacturer.

If the disc is clean and does not work in another drive, it is probably damaged and has to be replaced.

4. Clean the Drive

You can clean the disc drive by using a CD-ROM drive cleaning disc or DVD drive cleaning disc; these cleaning discs are available in most computer or home electronics stores. Before you purchase a drive cleaning disc, try to troubleshoot the issue by following the remaining steps in this article.

5. Test Disc Read with Copy or Xcopy

Copy and Xcopy are command-line utilities that typically uncover a disc-reading issue. If Copy and Xcopy complete successfully, the issue is unlikely to be a problem with reading the disc. A failure to copy may indicate drive problems or system problems; in that case, do more troubleshooting.

To use Copy and Xcopy to test disc-reading, follow these steps:

1. Click Start, and then click Run.

2. In the Open dialog box, type cmd, and then press ENTER.

3. At the command prompt, type one of the following commands: To copy a folder:

copy  discdrive:foldername   drive:psstest /V 

To copy the whole disk:

xcopy  discdrive:*.*  drive:psstest  /V /E 

NOTE: discdrive is the drive letter of the CD-ROM or DVD drive, foldername is the name of the folder containing files that you have to have to access on the disk, and drive is the letter of your system hard disk.

4. Press ENTER.

5. If you are prompted with the question whether psstest specifies a file name or directory name, press F.

6. If you are prompted to overwrite, press A.

NOTE: When you use /V with Copy or Xcopy, the copied files are verified. This takes longer but it makes sure that the files were copied correctly.

6. Quit Unnecessary Software

Software on your computer may interfere with reading the disc. For example, this may occur with antivirus software, firewall software, or anti-crash software. If you start your computer without unnecessary software, the computer may be able to read from the disc. Follow the steps in the following article: For additional information on how to start Microsoft Windows XP without unnecessary software, click the article number below to view the article in the Microsoft Knowledge Base:

310353 (http://support.microsoft.com/kb/310353/EN-US/) How to Perform a Clean Boot in Windows XP

After you have performed a clean boot of Windows XP, quit any remaining programs. To do so, follow these steps:

1. Quit all programs that are running.

2. Right-click each icon in the notification area, and then click Exit.NOTE: The notification area is located at the far right of the taskbar, near the clock. Some programs that are listed in the notification area do not have an Exit command on the shortcut menu, and you may have to click Quit, Close, or Disable, depending on the commands available for that program.

3. Press CTRL+ALT+DEL. In the Windows Security dialog box, click Task Manager.

4. In Windows Task Manager, click Applications.

5. No programs should appear under the Task list. If any programs appear, click the program name, and then click End Task.

6. Repeat step 5 until the Task list is empty.

7. Quit Windows Task Manager.

7. Switch the Drive Controller to DMA Mode

Switch the CD-ROM drive or DVD drive to DMA mode from PIO; this may resolve the issue. For additional information about how to switch your computer's drive controller to DMA mode, click the article number below to view the article in the Microsoft Knowledge Base:

310751 (http://support.microsoft.com/kb/310751/EN-US/) Device Settings Are Hard to Find in Windows XP

Website Designed &
Developed By